Magnetan Pocket-sized pulsed magnetic field for pain, mood, sleep, and more
NeuroTrek: Advanced Digital CES. The ultimate in Cranial Electrical Stimulation, More control of frequencies for neurotransmitter balancing, endorphin release, deep relaxation, sleep, IQ gains, and more.
Oasis: Miniature multipurpose microcurrent CES synchronized to pulsing lights and sounds!
Zappers: Electrical and magnetic stimulation for parasite elimination thru blood purification.
& Sound Mind Machines
PROTEUS: All the Orion programs and features with advanced PC link and BiColor lights!
Used Gear: Hot deals!
Magnetic Pulser MODEL #: MPG5
The First Aid Kit of the Future
High Intensity Momentary Time-Variant Pulsed DC Magnetic Field Therapy Generator
simple method of zapping parasites in hard-to-reach areas.
These units have not been evaluated by Health Canada or the FDA for
safety or effectiveness. Government regulators say that testimonials
are misleading and deceptive. Also, please understand that these
products are not intended to nor are they allowed to cure or treat
any specific disease. Government regulators state you must consult a
medical doctor for the treatment of all diseases.
NOTE: Health Canada has issued a Medical Device License (#28294) for The Magnetic Pulser. The MPG is classified as a Class II Medical Device, allowing for sale without a Medical Doctor's prescription.
The Magnetic Pulser is a professionally designed quality unit, thoroughly tested and guaranteed to operate as per the specifications. The Magnetic Pulser (MPG) is designed to generate an intense (~43,133 Gauss*), momentary (~2.5mS) pulsed DC magnetic field. For Gauss calculations, and an in-depth discussion on the electrical principles at play with an MPG, click HERE.
*This 43,133 Gauss measurement is at the inter-coil winding flux. Magnetic flux intensity follows the inverse square rule - the further you are away from the magnetic core, the faster the Gauss intensity drops off. At face of Magnetic Coil, the Gauss drops to ~6,000 Gauss.
NOTE: Please do not confuse this unit with permanent/ceramic magnet therapies, or with the EMR (electro-magnetic radiation) producing units!
Through the principle of induction, this magnetic field creates eddy-currents (tiny electrical micro-currents) in living organic material that contain an electrolyte such as saline. Designed to be used with a Colloidal Silver generator or independently. Targets specific areas.
New Features of model MPG5:
Quartz crystal Micro-Computer controlled functions for precise waveform generation and accurate timing sequences.
New Hand-Paddle design. Our pulsing coil has been re-designed into a custom molded plastic enclosure complete with clear identification of the Bio-North (-) Magnetic Pole.
A unique circuit design allows The Magnetic Pulser to operate without the use of a Xenon flashtube allowing for maximum power delivery to the coil.
Fully Automatic. The MPG5 will automatically charge and discharge - no manual pulsing required. An internal Digital Counter allows the MPG5 to pulse approximately 20 minutes between resets.
LED light bar-graph. A light bar-graph consisting of five Green LED lights, illuminates sequentially giving visual indication of the MPG5 charging up.
A Red LED light indicates either the unit has completed a 20 minute cycle of pulses, or an overload condition has occurred.
AUDIBLE output option. Unit beeps each time magnetic pulse is released to coil.
Operates from an AC-DC Wall Adapter (included), or from a 12 Volt DC source like an automobile battery, appropriate solar panel, etc.
Extremely high magnetic power output. Generates maximum 42.18 Joules (Watt*Seconds) of energy through the use of a 600uF, 330VDC Custom Photoflash Capacitor. This then produces ~43,133 Gauss* (~43 kilo Gauss) magnetic field in the coil. For Gauss calculations, and an in-depth discussion on the electrical principles at play with an MPG, click HERE. *This 43,133 Gauss measurement is at the inter-coil winding flux. Magnetic flux intensity follows the inverse square rule - the further you are away from the magnetic core, the faster the Gauss intensity drops off. At face of Magnetic Coil, the Gauss drops to ~6,000 Gauss.
High-Frequency Custom Switch Mode Pulse-Width-Modulated (PWM) power supply allows for fast charges (3.5 seconds) and a very lightweight unit. Our PWM power supply is a constant-current design.
Double-insulated practices used throughout to ensure the greatest electrical safety. Coil is completely enclosed in a custom-molded plastic Hand Paddle. No exposed wires or leads.
New Professional Capacitor. We now have a Professional Custom Strobe type Capacitor designed specifically for our Magnetic Pulser. The manufacturer rates the capacitor at well over a 30 million (30,000,000) cycles of operation. Compare this with our earlier version model MPG2 and MPG3 which had a 250,000 cycle life, or to our MPG1 which had a 85,000 cycle life, or even to photoflash based pulsers that have 5,000 - 10,000 life cycle.
Very Fast charging cycle. Unit fully charges in 3.5 seconds.
Overload Protection. Should an overload or fault condition occur in the charging section, a sensor will limit the current, then eventually shutdown the unit until the fault condition is removed.
Bio-North Magnetic Pole Polarity (-) or South-Seeking is clearly identified on one side of pulsing coil. This gives the user the choice of applying either Bio-North (-) or Bio-South (+) pole energy to the site.
Our Electrical Circuit Boards are GOLD Plated for extreme reliability and workmanship.
Compact and lightweight. MPG5 unit weighs 3/4 Lbs. (0.3 Kg.), Magnetic coil weighs 1 Lb. (0.4 Kg.). Total shipping weight of complete MPG5 with wall adapter weighs ~3 Lbs. (~1.3 Kg.).
The Magnetic Pulser is housed in a new custom plastic
enclosure. A pushbutton turns the Magnetic Pulser on and off. A series of Green lights indicates
power is available and visually shows unit is charging. When turned on, the Magnetic Pulser
will immediately begin to charge up (in about 3.5 seconds). When fully
charged, the stored energy of the capacitor is discharged into the pulsing coil.
The Red light will flash indicating the charge has been released.
The Magnetic Pulser will then begin another charge cycle.
Should an overload or fault condition occur in the charging section, the MPG5 will shutdown until the fault condition is removed. The unit will beep and flash the Red light notifying the user.
After approximately 20 minutes of pulsing, the MPG5
will go into stand-by mode until a physical reset occurs. This helps prevent
continuous operation should the MPG5 be left on unattended. If the unit is
not reset within 30 seconds it will turn itself off.
The Magnetic Pulser is packaged in a soft carrying case for easy storage.
The Magnetic Pulser is designed to
the highest standards. We have improved on the original design with
added features. Our electronic design is unique and efficient making the
unit very reliable and powerful. Early designs required the use of a
Xenon flashtube. We've completely re-designed The Magnetic
Pulser from the ground up using the latest in electronic components.
The result is a very powerful, reliable, rugged unit that transfers more
energy to the output coil. In addition, we use double-insulation
techniques to ensure the greatest in electrical safety. This is of
Specifications (as measured on a Tektronics TDS 210 Digital Real-Time Oscilloscope, and Wavetek AD105 Clamp-On RMS Ammeter)
Each Magnetic Pulser comes complete with:
The Magnetic Pulser MPG5 unit